不銹鋼玻璃門根據玻璃的不同類型和用途，可以分為以下幾種：

　　Stainless steel glass doors can be divided into the following categories based on the different types and uses of glass:

　　1.裝飾玻璃門 ：

　　1. Decorative glass door:

　　包括磨砂玻璃、壓花玻璃、刻花玻璃、釉面玻璃、噴花玻璃、冰花玻璃、乳化玻璃等。這些玻璃主要在于花紋和色彩的不同，具有極佳的裝飾效果和耐腐蝕性，易清洗，抗沖刷。

　　Including frosted glass, embossed glass, engraved glass, glazed glass, spray painted glass, ice glass, emulsified glass, etc. These glasses mainly have different patterns and colors, excellent decorative effects, corrosion resistance, easy cleaning, and abrasion resistance.

　　2.安全玻璃門 ：

　　2. Safety glass door:

　　包括鋼化玻璃、防彈玻璃、夾絲玻璃和夾層玻璃。這些玻璃具有良好的采光性、易清洗性、機械強度高、熱穩定性好，并且在碎裂后不飛散，有防搶、防盜、防火的作用。

　　Including tempered glass, bulletproof glass, laminated glass, and laminated glass. These glasses have good lighting, easy cleaning, high mechanical strength, good thermal stability, and do not scatter after shattering, with anti robbery, anti-theft, and fireproof functions.

　　3.節能玻璃門 ：

　　3. Energy saving glass door:

　　采用特殊工藝和著色，能有效吸收太陽輻射熱量，實現節能效果。

　　By using special techniques and coloring, it can effectively absorb solar radiation heat and achieve energy-saving effects.

　　安裝方法

　　Installation method

　　1.放線定位 ：

　　1. Cable laying and positioning:

　　在安裝之初，需要對固定玻璃隔斷及活動玻璃門扇統一放線定位，確定門框位置，并準確測量地面標高及門框頂部標高。

　　At the beginning of installation, it is necessary to uniformly lay out and position the fixed glass partition and movable glass door leaf, determine the position of the door frame, and accurately measure the ground elevation and the top elevation of the door frame.

　　2.安裝門框頂部限位槽 ：

　　2. Install the top limit slot of the door frame:

　　由所彈中心線引出兩條金屬裝飾板邊線，然后按邊線進行門框頂部限位槽的安裝。

　　Draw out two metal decorative panel edges from the center line, and then install the limit groove on the top of the door frame according to the edges.

　　3.安裝金屬飾面的木底托 ：

　　3. Install wooden base with metal veneer:

　　在原預埋木磚上釘方木，或通過膨脹螺栓釘方木，把方木固定在地面上，然后用膠將金屬飾面板粘在木方上。

　　Nail square timber onto the original pre embedded wooden bricks, or use expansion bolts to fix the square timber to the ground, and then use glue to stick the metal decorative panel to the timber.

　　4.安裝堅向門框 ：

　　4. Install the rigid door frame:

　　按所彈中心線釘立門框方木，然后用膠合板確定門框柱的外形尺寸和位置的固定，再外包金屬裝飾面。

　　Nail the door frame square timber according to the marked centerline, then fix the outer dimensions and position of the door frame column with plywood, and then wrap it with metal decorative surface.

　　5.玻璃門扇安裝 ：

　　5. Installation of glass door leaf:

　　使用玻璃吸盤器或玻璃吸盤機把厚玻璃吸緊吸住，通過2~3人把厚玻璃板抬起并豎立起來移至安裝地點準備就位。

　　Use a glass suction cup or a glass suction cup machine to tightly suck the thick glass, and have 2-3 people lift and stand the thick glass plate to move it to the installation site for preparation.

　　6.玻璃固定 ：

　　6. Glass fixation:

　　在底托木上的內外釘兩根扁方木條把厚玻璃夾在中間，留出適當空隙，然后在扁方木條上涂刷全能膠將飾面金屬板粘卡在方木及兩根扁方木條上。

　　Nail two flat square wooden strips inside and outside the bottom support wood to sandwich the thick glass in the middle, leaving a suitable gap. Then apply universal glue on the flat square wooden strips to stick the decorative metal plate to the square wood and the two flat square wooden strips.

　　7.注玻璃膠封口 ：

　　7. Glass glue sealing:

　　在頂部根位槽雙側空隙內及底托玻璃槽口的雙側和厚玻璃與門框柱的對接處注入玻璃膠。

　　Inject glass glue into the gaps on both sides of the top root groove and the joint between the thick glass and the door frame column on both sides of the bottom glass groove.

　　8.玻璃之間對接 ：

　　8. Docking between glasses:

　　對于寬度尺寸過大的固定部分厚玻璃板，需用兩塊玻璃拼接，并在中間夾入金屬條，涂上膠固定。

　　For fixed thick glass panels with excessive width dimensions, two pieces of glass need to be spliced together, with a metal strip sandwiched in the middle and coated with adhesive for fixation.

　　建議

　　Suggestion

　　在安裝過程中，務必注意玻璃的平整度和垂直度，確保門的密封性能和美觀效果。

　　During the installation process, it is essential to pay attention to the flatness and verticality of the glass to ensure the sealing performance and aesthetic effect of the door.

　　使用專業的安裝工具和材料，如玻璃吸盤器、萬能膠、玻璃膠等，以確保安裝質量和安全。

　　Use professional installation tools and materials, such as glass suction cups, universal glue, glass glue, etc., to ensure installation quality and safety.

　　在安裝完成后，進行全面的檢查，確保所有連接件都牢固無松動，玻璃無破損。

　　After installation, conduct a comprehensive inspection to ensure that all connections are secure and not loose, and that the glass is not damaged.

　　本文來自：山東不銹鋼玻璃門更多的內容請點擊：http://www.8vc.net我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！

　　This article is from Shandong Stainless Steel Glass Doors. For more content, please click: http://www.8vc.net We will provide satisfactory service for the questions you ask. Welcome to call us!